• Теги этой статьи
  • Инструкция по разборке ноутбука Asus UL80J, замена разъёма питания [ENG]

    In this guide I will be taking apart an Asus UL80J laptop in order to repair damaged DC power jack.

    As you see on the following picture, the DC jack got pushed into the case to the point that the AC adapter will not plug in anymore.

    I will disassemble this computer, show why it happened and how to repair the problem without buying any spare parts.

    During the disassembly process I’ll go though the following major steps:

    • ШАГ 1-5: Accessing both RAM modules. Removing the hard drive and optical drive;
    • ШАГ 6-13: Disconnecting and removing the keyboard;
    • ШАГ 14-22: Removing the top cover (palm rest) assembly;
    • ШАГ 23-24: Removing and disconnecting the cooling fan;
    • ШАГ 25-29: Fixing damaged DC jack.

    Let’s start.

    ШАГ 1.

    First of all, make sure the computer is turned off.

    Unlock and remove the battery.

    ШАГ 2.

    Remove screws securing the hard drive and RAM (memory) covers.

    Remove both covers.

    NOTE: it’s not necessary to remove the RAM cover for the purpose of my repair. I’m doing that just to show how to access RAM slots.

    ШАГ 3.

    Slide the hard drive to the right to disconnect it from the motherboard.

    ШАГ 4.

    Lift up and remove the hard drive assembly.

    ШАГ 5.

    Remove two screws securing the optical drive.

    Slide the optical drive to the left and remove it.

    ШАГ 6.

    The keyboard is secured to the case by four tiny latches.

    ШАГ 7.

    Push the left latch into the case using a small flat head Phillips screwdriver.

    ШАГ 8.

    While the latch is pushed in, lift up the corner of the keyboard so the latch doesn’t lock back.

    Unlock all remaining latches.

    ШАГ 9.

    Now you can separate the upper side of the keyboard from the case.

    Turn the keyboard over and place it upside down on the palmrest.

    ШАГ 10.

    Now you can access the keyboard cable connector.

    ШАГ 11.

    Here’s how to unlock the keyboard connector.

    Carefully lift up the left side of the cable retainer with your fingernail.

    The retainer will open up at a 90 degree angle.

    ШАГ 12.

    After the connector is unlocked, you can pull the cable.

    ШАГ 13.

    Remove the keyboard from the laptop.

    ШАГ 14.

    Remove all shown screws from the bottom.

    ШАГ 15.

    Remove screws securing the top cover assembly.

    Disconnect two cables.

    ШАГ 16.

    Here’s how to unlock the connector located closer to the cooling fan.

    It’s similar to the keyboard connector shown in steps 11 and 12.

    ШАГ 17.

    The trackpad connector is a little bit different.

    In order to unlock the connector you’ll have to slide the cable retainer about 2-3 millimeters towards the trackpad.

    NOTE: the retainer must remain attached to the connector base.

    ШАГ 18.

    On the following picture the trackpad connector shown in the unlocked state.

    Now you can pull the cable from the connector.

    ШАГ 19.

    Start separating the top cover assembly from the base using a guitar pick (or any other piece of plastic).

    ШАГ 20.

    Continue separating the top cover assembly from the bottom.

    ШАГ 21.

    The top cover (palm rest assembly) has been removed.

    Here’s a picture of the bottom side of the top cover assembly.

    ШАГ 22.

    After the top cover removed, you can access all internal components.

    In the following two steps I’ll show how to remove the cooling fan. It’s not necessary for the purpose of my repair but the fan looks dirty and I’ll clean it up.

    ШАГ 23.

    Remove two screws securing the cooling fan.

    ШАГ 24.

    Lift up the cooling fan and disconnect the cable.

    Now you can clean up the fan and heat sink if they are dusty.

    ШАГ 25.

    Finally, let’s take a look at the DC jack.

    As you see, the DC jack dislocated from its normal position.

    The left side of the jack should almost touch the case but it’s located about 5-6 millimeters away from the case.

    Remove one screw securing the metal bracket to the case and remove the DC jack with the bracket.

    ШАГ 26.

    Now you can see why the DC jack got dislocated.

    The jack had support walls behind and they are broken.

    Apparently, the laptop was dropped while being plugged into the AC adapter and landed on the power plug.

    Remove all broken and loose plastic pieces.

    ШАГ 27.

    Instead of replacing the entire bottom cover I’ll do some modification to the DC jack.

    I’ll use a piece of rubber as a support wall for the DC jack. Probably a regular pen eraser will work just fine for that.

    ШАГ 28.

    Install the rubber piece so it fits behind the jack.

    Make sure the rubber piece has correct heights and the DC jack seats properly.

    After it fitted, you can glue the rubber piece to the bottom case.

    ШАГ 29.

    Install the DC jack back in place and make sure it’s secured.

    As you see, the rubber piece fitted very tightly behind the jack and supports it very well.

    Всё! Ноутбук разобран. Сборка происходит в обратном порядке, если у вас возникнут сложности вы всегда можете обратиться к специалистам.

    Источник: www.insidemylaptop.com


    Компьютерный мир

    Вся информация на страницах сайта предназначена только для личного не коммерческого использования, учёбы, повышения квалификации и не включает призывы к каким либо действиям.

    Частичное или полное использование материалов сайта разрешается только при условии добавления ссылки на непосредственный адрес материала на нашем сайте.