• Теги этой статьи
  • Инструкция как разобрать ноутбук Acer TravelMate 3260 [ENG]

    In this guide I will disassemble an Acer TravelMate 3260 laptop.

    I will show how to remove and replace the power board which has DC jack on it.

    Most likely my guide will work for some other Acer TravelMate models. If it works for you, please mention the model number in comments after the post.

    In Acer TravelMate 3260 power from AC adapter goes to the motherboard through the power board. If your laptop stopped charging the battery or will not run from AC adapter, you should check the power board.

    ШАГ 1.

    First of all, turn off the computer and remove the battery.

    Remove two screws securing the switch cover on the back.

    ШАГ 2.

    Start removing the switch cover and lift it up by the hinge cover. Continue removing the cover with your hinges.

    ШАГ 3.

    Remove the cover.

    ШАГ 4.

    Remove two screws securing the keyboard.

    ШАГ 5.

    Carefully separate the keyboard from the top cover and place it upside down on the palm rest so you can access the cable connector.

    ШАГ 6.

    You have to unlock the connector before you can pull the cable.

    On the picture below you see the connector in the unlocked position. Now you can release the cable.

    The keyboard has been removed.

    ШАГ 7.

    Remove the hard drive and memory covers.

    ШАГ 8.

    Remove one screw securing the hard drive assembly.

    ШАГ 9.

    Pull the hard drive to the left and disconnect it from the motherboard. Remove the hard drive.

    ШАГ 10.

    Remove one screw securing the optical CD/DVD drive to the base. Push the drive from the laptop with your finger. Remove the optical drive.

    It is not necessary to disconnect memory modules, wireless card, modem card and CMOS (RTC) battery for the purpose of my guide . You can leave them connected to the motherboard.

    ШАГ 11.

    Remove all marked screws from the bottom case. Disconnect cables I pointed with yellow arrows. Disconnect two antenna cables from the wireless card (green arrows).

    ШАГ 12.

    Remove one screw from the back side.

    ШАГ 13.

    Disconnect the video cable connector. Unroute both Wi-Fi antenna cables and pull them through the opening in the motherboard. Remove four screws securing LCD panel hinges.

    ШАГ 14.

    Remove the LCD panel.

    ШАГ 15.

    Remove five screws securing the top cover assembly. Disconnect the touchpad cable.

    ШАГ 16.

    Start separating the top cover assembly from the bottom case.

    ШАГ 17.

    Remove the top cover assembly.

    ШАГ 18.

    Remove two screws securing the motherboard.

    ШАГ 19.

    Start removing the motherboard from the top left corner.

    Release and lift up the top right corner of the board.

    Carefully pull the motherboard from the bottom case.

    ШАГ 20.

    On the picture below you see the power board attached to the motherboard.

    The DC power jack and power switch are located on the power board.

    Remove two screws securing the power board.

    Disconnect the power board from the motherboard.

    The power board part number is printed right in the middle. It’s DA0ZR1PB6D1 (REV:D).

    ШАГ 21.

    While the motherboard is removed from the base, you can clean the cooling module. Loosen six screws securing the heat sink assembly. Disconnect the fan cable from the motherboard.

    Remove the heat sink assembly and blow off dust using compressed air.

    Всё! Ноутбук разобран. Сборка происходит в обратном порядке, если у вас возникнут сложности вы всегда можете обратиться к специалистам.

    Источник: www.insidemylaptop.com


    Компьютерный мир

    Вся информация на страницах сайта предназначена только для личного не коммерческого использования, учёбы, повышения квалификации и не включает призывы к каким либо действиям.

    Частичное или полное использование материалов сайта разрешается только при условии добавления ссылки на непосредственный адрес материала на нашем сайте.